Use this process when a complete panel or component needs a uniform refreshed appearance. Complete-panel renewal is generally more suitable than a local touch-up where the existing finish has aged or faded.
Check the entire panel or component for fading, chalking, gloss loss, scratches, previous repairs, loose coating, corrosion and exposed metal. Confirm the substrate is suitable for re-coating.
Create a clean, ventilated and controlled spray area. Protect adjacent surfaces, glass, equipment, vehicles and property.
Wash to remove dirt and contamination, then clean away oil, wax, grease, silicone and other contaminants. Allow the surface to dry completely.
Sand the complete surface with 600 grit abrasive paper or ultra fine abrasive pad. Do not sand through sound powder coat unnecessarily.
Feather scratches and chips into sound coating. Remove corrosion and loose material. For any exposed bare metal, prime with Dulux MetalShield Etch Primer before applying Powdercoat Renew.
Do not skip cleaning or sanding, spraying over corrosion, applying one heavy coat, holding the can too close and not masking all areas.
Dulux Powdercoat Renew - A professional recoating system designed to restore, recolour and extend the life of powder-coated surfaces.
Remove all sanding dust, then wipe the area clean. The surface must be sound, clean, dry and free from contaminants before coating.
Mask glass, seals, hardware and adjacent surfaces. Leave enough space around the damage to blend the repair and protect against overspray.
Prime exposed metal with Dulux MetalShield Etch Primer before applying Powdercoat Renew. Do not apply directly over rust, corrosion or untreated bare metal.
Shake the can thoroughly for 2 minutes once the ball rattles. Test spray onto a suitable surface to confirm spray pattern, product flow and colour suitability before spraying the asset.
Hold the can approximately 20–25 cm from the surface. Use long, even passes with consistent speed and distance. Slightly overlap each pass and work methodically across the full panel or area. Apply multiple light coats, rather than one heavy coat, allowing 1–2 minutes between each light coat. Amount of coats will depend on colour and surface colour. Avoid spraying if temperatures are below 15°C, high humidity or when raining.
Carefully remove masking around the repair area while the paint is still wet. Coating will be touch dry in 10 minutes and dry to handle in 1 hour at 25°C. Inspect colour, coverage, sheen, edges. The area can be recoated after 10 minutes if required.
How do I restore faded or chalky powder coat?
Renew the complete panel or component:
Inspect the whole surface.
Deep clean it.
Sand the whole area with 600 grit abrasive.
Repair chips, and prime any bare metal with Dulux MetalShield Etch Primer.
Re-clean and mask.
Apply multiple light coats of Dulux Powdercoat Renew using long, even, slightly overlapping passes.
Can I change the colour of powder coat with Dulux Powdercoat Renew?
Yes. Renewing a full panel or complete component with Dulux Powdercoat Renew can recolour a suitable powder-coated asset. For an even result, prepare and coat the whole surface by following the How to Renew guide.
Can Dulux Powdercoat Renew match faded powder coat?
Not always. Each Dulux Powdercoat Renew colour is matched to an approved Dulux standard, not to an aged installation. If the existing surface has faded, renewing the full panel or component usually gives a more consistent result than a touch-up.
Should I touch up or renew my powder coat?
How do I prepare powder coat before repainting?
Do I need a primer? Can I spray over rust or bare metal?
Should I buy all the cans I need at once?
Can I use printed colour chips or on-screen colours to approve the colour?
How many coats of Dulux Powdercoat Renew do I need?
How far away should I hold the spray can?
What weather conditions are best for spraying?
How long does Dulux Powdercoat Renew take to dry?
Can I apply Dulux Powdercoat Renew indoors?
What safety gear do I need to use Dulux Powdercoat Renew?
Who can I contact for technical advice on Dulux Powdercoat Renew?
Touch up small, localised damage, ideally no larger than 5 cm × 5 cm. Renew the complete panel or component when fading, ageing, larger damage or an even appearance is the main concern.
Wash off dirt, then remove oil, wax, grease and silicone with wax and grease remover on a lint-free cloth. Sand with P600 grit paper or an ultra-fine 600 grit pad, without sanding through sound powder coat. Remove all sanding dust, and make sure the surface is clean and dry before applying Dulux Powdercoat Renew.
Don't apply Dulux Powdercoat Renew directly over rust, corrosion or untreated bare metal. Remove corrosion and loose material first, then prime any exposed bare metal with Dulux MetalShield Etch Primer before applying Dulux Powdercoat Renew.
Yes. Buy enough Dulux Powdercoat Renew in one visit for the complete job. This reduces colour variation between cans and between store visits.
No. Printed and on-screen colours are only a guide. Always compare the actual sprayed Dulux Powdercoat Renew against the asset before final approval.
Apply at least 2 coats. The exact number depends on the paint colour and the colour of the surface underneath. Apply several light coats rather than one heavy coat, allowing 1–2 minutes between coats.
Hold the can about 20–25 cm from the surface. First, shake it for 2 minutes once the ball rattles, and test spray on a suitable surface. Use smooth, even passes at a consistent speed and distance, slightly overlapping each pass.
Spray Dulux Powdercoat Renew in dry, well-ventilated conditions. Avoid spraying when the temperature is below 15°C, when humidity is high or when it's raining.
Dulux Powdercoat Renew is touch dry in 10 minutes and dry to handle in 1 hour at 25°C. It can be recoated after 10 minutes if needed.
Indoor application is not recommended. Only coat indoors if you can meet the label and Safety Data Sheet (SDS) requirements, including suitable ventilation, PPE, overspray control and management of ignition risks.
Read the label, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) first. Wear safety glasses, protective gloves, long sleeves and enclosed footwear, plus a P2 mask or other respiratory protection where required. Spray in a well-ventilated area away from heat, sparks and flames. The can is pressurised, so never puncture or burn it.
Contact Dulux Help and Advice on 13 23 77 or visit duluxtrade.com.au.