Use touch-up only for small, localised damage. If the surface is faded, extensively damaged or appearance uniformity is critical, renew the complete panel or component. It is recommended to keep touch-ups within 5 cm × 5 cm. This helps minimise noticeable differences in colour and sheen over time, while aiming to retaining as much of the original powder-coated finish as possible.
Check for loose coating, corrosion, exposed metal or wider coating failure. If damage is extensive, stop and use the full renewal process or obtain technical advice.
Remove loose dirt and dust, corrosion and rust. Clean away grease, wax, oil, silicone and other contaminants with wax and grease remover on a clean lint-free cloth and allow the area to dry completely.
Using a 600 grit abrasive, sand the damaged area and feather the edges into the surrounding sound powder coat. Remove sharp edges around chips without unnecessarily enlarging the repair.
Do not skip cleaning or sanding, spraying over corrosion, applying one heavy coat, holding the can too close, or expect an invisible match to the original powder coated asset.
Dulux Powdercoat Renew - A professional recoating system designed to restore, recolour and extend the life of powder-coated surfaces.
Remove all sanding dust, then wipe the area clean. The surface must be sound, clean, dry and free from contaminants before coating.
Mask glass, seals, hardware and adjacent surfaces. Leave enough space around the damage to blend the repair and protect against overspray.
Prime exposed metal with Dulux MetalShield Etch Primer before applying Powdercoat Renew. Do not apply directly over rust, corrosion or untreated bare metal.
Shake the can thoroughly for 2 minutes once the ball rattles. Test spray onto a suitable surface to confirm spray pattern, product flow and colour suitability before spraying the asset.
Hold the can approximately 20–25 cm from the surface. Start each pass just before the repair, move smoothly across it and release after clearing the area. Apply several light coats rather than one heavy coat allowing 1–2 minutes between each light coat. Avoid spraying if temperatures are below 15°C, high humidity or when raining.
Carefully remove masking around the repair area while the paint is still wet. Coating will be touch dry in 10 minutes and dry to handle in 1 hour at 25°C. Inspect colour, coverage, sheen, edges. The area can be recoated after 10 minutes if required.
How do I touch up chipped or scratched powder coat?
To touch up powder coat with Dulux Powdercoat Renew:
Clean the area with wax and grease remover.
Sand and feather the edges with 600 grit abrasive.
Re-clean, then mask surrounding surfaces.
Prime any bare metal with Dulux MetalShield Etch Primer.
Shake the can for 2 minutes.
Apply several light coats from 20–25 cm away.
Remove the masking while the paint is still wet.
How large can a powder coat touch-up be?
The recommended maximum touch-up area with Dulux Powdercoat Renew is 5 cm × 5 cm. Keeping touch-ups small helps minimise noticeable differences in colour and sheen over time, while keeping as much of the original powder-coated finish as possible.
Should I touch up or renew my powder coat?
Touch up small, localised damage, ideally no larger than 5 cm × 5 cm. Renew the complete panel or component when fading, ageing, larger damage or an even appearance is the main concern.
Why might a touch-up still be visible?
The original powder coat may have aged or faded. Differences in sheen, paint thickness or local application can also make a repair visible, and lighting and batch-to-batch variation affect the result. A touch-up won't be an invisible match to the original powder coat.
What should I do if the colour match isn't acceptable?
Do I need a primer? Can I spray over rust or bare metal?
How many coats of Dulux Powdercoat Renew do I need?
What weather conditions are best for spraying?
How long does Dulux Powdercoat Renew take to dry?
Can I apply Dulux Powdercoat Renew indoors?
Who can I contact for technical advice on Dulux Powdercoat Renew?
Spray a representative test panel and compare it with the actual item in natural daylight before you start the project. This is the most reliable way to confirm the colour and sheen of Dulux Powdercoat Renew against your asset.
Stop before coating the asset. Recheck the colour, sheen, surface age and your spraying technique, then contact Dulux technical or colour support. Renewing the full panel may be the better option.
Don't apply Dulux Powdercoat Renew directly over rust, corrosion or untreated bare metal. Remove corrosion and loose material first, then prime any exposed bare metal with Dulux MetalShield Etch Primer before applying Dulux Powdercoat Renew.
Apply at least 2 coats. The exact number depends on the paint colour and the colour of the surface underneath. Apply several light coats rather than one heavy coat, allowing 1–2 minutes between coats.
Spray Dulux Powdercoat Renew in dry, well-ventilated conditions. Avoid spraying when the temperature is below 15°C, when humidity is high or when it's raining.
Dulux Powdercoat Renew is touch dry in 10 minutes and dry to handle in 1 hour at 25°C. It can be recoated after 10 minutes if needed.
Indoor application is not recommended. Only coat indoors if you can meet the label and Safety Data Sheet (SDS) requirements, including suitable ventilation, PPE, overspray control and management of ignition risks.
Contact Dulux Help and Advice on 13 23 77 or visit duluxtrade.com.au.